WPCR 2BTgW#|d Elite 10pt 12 pitch (D/J/M)|Lddd,#d\( @HP LaserJet Series IIHPLASEII.PRSd\( @,,,,06O2D%L Tq W#|dPrestige Elite 10pt 12 pitch (D/J/M)|Lddd,#d\( @HP LaserJet Series IIHPLASEII.PRSd\( @,,,,06O2N NJP* +* * * * * * * * REMOVE THIS OUTLINE GUIDE BEFORE PLACING THE SPECIFICATION SECTION IN THE CONTRACT ,* * * * * * * * 'O U T L I N E G U I D E &DIVISION 17: MISCELLANEOUSă AERIAL APPLICATION OF HERBICIDE SOLUTION SPECIFICATION NO. 17220  * * * * * * * * * * * * * * * * * * * * * * * * * * * * X  * NOTICE TO DESIGNER!! *(# X  * *(# X X`  * 1. DO NOT USE DIVISION 1 thru 16 SPECIFICATIONS * * SPECIFICATIONS WITH THIS SPECIFICATION. *(#` X X`  * *(#` X X`  * 2. Check with procurement personnel for wording *(#` * on the following: * * * X X`  * Section F Work Progress *(#` X X`  * Section G Project Inspection *(#` * Section H Work Hours * * Section J Drawings * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * X (# USE:XEradication of vegetative cover using herbicides in solution, aircraft, and other equipment.X` hp x (#%'X` hp x (#%'(# DRAWING DATA REQUIRED: Location, and detail drawings as needed. REQUIRED SPEC MODIFICATIONS: -GENERAL NOTESă X 1. Whenever entire articles, paragraphs or subparagraphs are not applicable, the articles, paragraphs or subparagraphs should be deleted; when necessary, reletter or renumber articles, paragraphs or subparagraphs.(# X 2. THIS GUIDE IS NOT INTENDED AS A SUBSTITUTE FOR READING THE ENTIRE SECTION.(#  h)Ԍ ,TECHNICAL NOTESă X 1.C.1.1: Select applicable words.(# X 2.C.1.2: Insert county and state where work will be performed.(# X 3.C.1.3: Insert access requirements.(# X 4.C.1.4: Insert applicable EPA Regulations.(# X 5. C.1.5: Delete when Government-furnished herbicide is used.(# X 6.C.1.5: Insert number of copies of certification required. Normally 3 copies are required. Distribution after review is normally 1 copy to the COR, 1 copy to the Contractor, and 1 copy to the project file.(# X 7.C.1.6: Describe how work limits are to be identified.(# X 8.C.1.7: Select applicable phrase.(# X 9. C.1.8: Insert applicable limits.(# 10.C.1.9: Describe special requirements.(# 11.C.1.10: Select applicable word and complete number of flagpersons required.(# 12.C.1.11: Select applicable word.(# 13.C.3.0: Delete when Government-furnished herbicide is used.(# 14. C.3.1.a: Select applicable words. 15.C.3.1.b: Describe herbicide to be used.(# 16.C.3.2.b: Select type of aircraft to be used and complete aircraft speed.(# 17.C.3.3: Select applicable description of spray nozzles.(# 18. C.3.3: Insert droplet size, when applicable. 19. C.3.4: Describe special aircraft requirements. 20.C.4.0: Delete when herbicide is Contractorfurnished.(# 21.C.4.1.a: Insert location where Governmentfurnished herbicide can be obtained.(# 22.C.4.1.b: Insert hours Governmentfurnished herbicide can be obtained.(# 17220 h)Ԍ 23.C.4.1.c: Insert location where Governmentfurnished herbicide is to be returned to.(# 24.C.4.1.d: Select applicable words.(# 25.C.4.2: Delete when Contractorfurnished herbicide is used.(# 26.C.4.2: Complete as appropriate.(# 27. C.4.3: Delete when Contractorfurnished herbicide is used. 28.C.5.1: Insert applicable wind speed.(# 29.C.5.4: Include words in brackets when required, and describe spray formula.(# 30.C.5.5: Insert rate of spraying.(# 31.C.5.6: Insert swath width.(# 32.C.5.8: Insert percent variance allowed.(# 33.E.4.2: Complete method of measurement, (i.e. field traverse, aerial photograph - dot grid, or map).(# 34. E.5.1: Select applicable Pay Items. Do not change Pay Item number. When Government-furnished property is specified for Pay Items, the letter suffix GF will be added after the parenthesis of the item number.(# X` hp x (#%'@ X !=* * * * * * * * * * * * * * * @ =* POINT OF CONTACT * DATE OF LAST REVISION: 8/03/89+=* Dave Kathman (SC325A) * WRITTEN BY: Forms 7410-9, 7410-10, and3=* FTS 776-0145 * DSC Forms 1510-2 and 1510-3,=* COMM. (303) 236-0145 * REVISED BY: Porter (SC673) *=* * * * * * * * * * * * * * * APPROVED BY: 17220 h)Ԍ,17220C@ X@ Xt{ SECTION C DESCRIPTION/SPECS./WORK STATEMENT AERIAL APPLICATION OF HERBICIDE SOLUTION SPECIFICATION NO. 17220 Rev. 889C.1.0 GENERAL: @ Xl XC.1.1lDescription of Work: Application of herbicides in solution with [Contractor- furnished] [and] [Government-furnished] property using aircraft.(#l C.1.2lLocation: Work under this Contract is located in [_________________] County, [___________________]. The work locations are shown on the drawings.(#l C.1.3lAccess to the Work: [_______________________________________](#l lGeneral Information and Requirements7XFSection 01009 lGovernment-Furnished Property0XFSection 01018 lMobilizationXFSection 01505 C.1.4lReferences:(#l  la. [__ __________________.](#l C.1.5lCertification: Furnish [ ] copies of written certification from the supplier of the Contractor-furnished herbicide that it conforms to the requirements of this specification.(#l C.1.6lWork Limits: The Government will define with [ ] the outer perimeter of areas to be treated and areas within such perimeter which are to be excluded from herbicide application.(#l C.1.7lLanding Facilities: [The Contractor shall obtain required landing facilities.] [Landing facilities are located as shown on the drawings.] The Contractor assumes full responsibility and liability for airstrips or landing areas used.(#l C.1.8lEnvironmental Conditions: Aircraft will not be allowed to spray or turn within [ ] mile of agricultural crops or residences having plants susceptible to damage from herbicide when using fixed-wing aircraft or helicopters; capable of applying spray at speeds of [ ] mph or less.(#l  (#ԌC.1.9 Special Requirements: [ .] l Xl XC.1.10ldFlagpersons: Shall be furnished by the [Government] [Contractor]. (#  ld[ ] flagpersons shall be simultaneously visible at the beginning of each spraying run and at least [ ] flagperson visible throughout the run for the pilots.(# C.1.11ldFlagging Materials and Equipment: Shall be furnished by the [Government.] [Contractor.](# C.2.0lDEFINITIONS: None.(#l l X@ XC.3.0 CONTRACTORFURNISHED ITEMS: C.3.1 Herbicide: @ X@l X @,la.Delivery: Deliver Contractor-furnished [herbicide] [and] [oil-phase formulation] [water-phase formulation] [water] [carrier, including wetting agent] in original, unopened containers.(#  @,lb.Herbicide: Shall conform to the following: [ ].(# C.3.2lAircraft:(#l  @,la.General: The Contractor shall furnish aircraft to apply herbicide in solution to the designated areas in the time specified.(#  @,lb.Type: Aircraft used shall be [unrestricted] [unrestricted, except capable of applying herbicide at [ ] mph minimum] [fixed wing only capable of applying spray at [ ] mph maximum] [helicopter only].(# C.3.3lSpray Nozzles: [Aircraft shall be equipped with nozzles, capable of uniform distribution at the specified rate. Nozzles will be directed with the slipstream or a maximum of 10 degrees downward. No nozzles are to be placed within 3 ft of each wing tip on fixed wing tip vortices. Systems must have positive liquid shut-off using one of the following: (1) individual nozzle check valves plus suckback device; (2) individual nozzle check valves plus boom pressure release device; or (3) individual nozzle positive-action valves.] [Aircraft shall be equipped with a system adapted for the application of thickened "invert" emulsion (water-in-oil) sprays. The "invert" emulsion shall be discharged from appropriate spray tips which will produce droplet size of from [ ] to [ ] microns. Spray tips will not be closer than 3 ft from wing tips on fixed wing planes. The system must have positive shutoff.](#l  (#ԌC.3.4lSpecial Aircraft Requirements: [ ].(#l C.3.5lMixing Equipment: [Contractor shall furnish the agitator and mixing tank for mixing spray material.] [The Contractor shall furnish metered mixing tanks for mixing either or both of the oil and water phases of the spray material. Fluids shall be measured by meters before and while loading in the aircraft to assure that the proper mix is obtained.](#l C.3.6lPilots: Shall be furnished by the Contractor and shall meet certification requirements of Federal Aviation Regulations for this type of work.(#l C.3.7lGround Crew: Shall be furnished by the Contractor.(#l C.4.0lGOVERNMENTFURNISHED PROPERTY:(#l C.4.1lDelivery, Storage, and Handling:(#l  @,la.Location: The Governmentfurnished herbicide will be provided by the Bureau of Land Management [_____________________________________.](#  @,lb.Time: Property will be available Monday through Friday, [________] except on holidays.(#  @,lc.Return of Unused Property: Return unused material to [_________].(#  @,ld.Loading/Off Loading/Transporting Property: The Contractor shall be responsible for providing the necessary materialhandling equipment to load/off load materials. [The Contractor shall load and transport [materials] [equipment] to worksites.](# C.4.2lEquipment to be Furnished by the Government:(#l  @,ld,  @l X@l hD8X +D9 Estimated(#D  @,lDescriptionh*Equipment3D9 QuantityDXF Unit(#X C.4.3lTransportation of Herbicide: The Contractor shall load and transport Government-furnished herbicide from the location specified to the worksite and between sites. Upon completion of the work or termination of the Contract, unused herbicide shall be returned by the Contractor to the location specified.(#l C.5.0lSPECIFIC TASKS:(#l (#ԌC.5.1lSpray Formula: Herbicide [and carrier, including wetting agent] specified shall be mixed by the Contractor in the following proportions: (#l  @,l[ ].(#l C.5.2lWind Conditions: Aerial spraying shall not be done when the wind is not at a constant velocity or exceeds [ ] mph.(#l C.5.3lFlight Paths: Flagpersons shall insure straight and regular paths of flight. Irregular paths of flight will result in immediate stoppage of work. Corrective action shall be taken immediately by the Contractor to insure evenly spaced, straight, and regular flight paths and complete coverage of areas included in the spraying job.(#l C.5.4lCoverage: The entire surface within the designated boundaries of the project area shall receive uniform coverage with the herbicide except for areas excluded by the Government. Areas excluded from the spraying operation within the designated boundaries, will not be included in the acreage computed for payment.(#l C.5.5lRate of Application: Herbicide shall be distributed at the rate of [ ] lb acid equivalent of herbicide per acre.(#l C.5.6lSwath Width: Shall not exceed [ ] ft.(#l C.5.7lFlight Height: Shall be low enough to obtain proper distribution and uniform coverage of herbicide. Spraying shall not be done during or after a rainstorm until the vegetation has dried. Aircraft shall be operated according to Federal Aviation Regulations.(#l C.5.8lFlight Strips: Shall be patterned and flown to secure a uniform distribution of herbicide. Such distribution shall not more than [ ] % above or below the average distribution of herbicide per acre.(#l C.5.9lTests for Uniformity: The Contracting Officer will make tests to determine uniformity of herbicide application.(#l C.5.10ldTests for Rate of Application: Rate of herbicide application will be determined from test flights and strip tests made prior to commencement of spraying operations to establish setting of the distribution mechanism.(#  ,END OF SECTION ! + /SECTION E AERIAL APPLICATION OF HERBICIDE SOLUTION SPECIFICATION NO. 17220 Rev. 489+17220E... !SECTION E INSPECTION AND ACCEPTANCE AERIAL APPLICATION OF HERBICIDE SOLUTION NO. SECTION 17220 Rev. 889 .x17220EE.1.0l52.252-02 CLAUSES INCORPORATED BY REFERENCE (APR 1984)(#l  @,lThis contract incorporates the following clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available.(#l  @,lI. FEDERAL ACQUISITION REGULATION (48 CFR CHAPTER 1) CLAUSES(#l  @ ,l 52-246-04 Inspection of Services - Fixed-Price (Apr 1984)(#l E.2.0lINSPECTION:(#l  @,lThe Contracting Officer will make periodic inspections as a basis for payments and recommendations for adjustments in work quality. The Contractor is encouraged to observe inspections while they are being made and have a supervisor on site to confer with the Contracting Officer.(#l E.3.0lACCEPTANCE:(#l  @,lWork performed according to the specifications and Part III will be considered acceptable for payment purposes.(#l E.4.0lMEASUREMENT OF PAYMENT:(#l E.4.1lUnits: Application of herbicide solution will be measured and paid for by the number of acres sprayed to the nearest whole acre.(#l E.4.2lMeasurement: The determination of the acreage of completed work will be made from [ ]. Area measurements required under this Contract will be measured on a horizontal plane.(#l E.4.3lRemeasurement: Remeasurement of the acreage under this Contract will be made upon the written request of the Contractor. The request for remeasurement must be made in writing within 10 calendar days after completion of the work. If remeasurement indicates a difference of not more than 5 percent from the original measurement, the Contractor shall pay the actual cost of the remeasurement. Payments will be based on the second measurement where the difference between measurement is more than 5 percent. Where the difference is less than 5 percent, the results of the first measurement will be used.(#l  `"ԌE.5.0lBASIS OF PAYMENT:(#l E.5.1lPayment: Prices and payment will be full compensation for the work described in this section. Payment will be made under:(#l @Pay Item  Pay Unit 17220(1) Aerial Spraying (Unrestricted aircraft). . . . . .Acre 17220(2) Aerial Spraying (Fixed wing) . . . . . . . . . . .Acre 17220(3) Aerial (Spraying Helicopter) . . . . . . . . . . .Acre ,END OF SECTION