WPC 2QBR Z Courierw Roman#|dOed6X@`7@HP LaserJet 4HPLAS4.PRS 4d6X@;\*"P@lr5ddd,Oed6X@`7@s4ddd,鑡d `7r5ddd,d6Nhez7HrV&PƋ΋ߋ~XrAuڋF&&&+=&|I&&+=&|&&-&%ddddddddddddddddddddddddddddddddddddddddNEssEX`AT`````6=`:=`:AATT`BBs``uEssErkkAT`:"`soh`kss`t 4HPLAS4.PRS 4?f\  P6G;\*"P?P2$r 0CourierCourier Bold X` hp x (#%'0*,.8135@8:, P age,  s5  F ooter, B , E dit. Delete the "Project Name (ftr B)" text and replace  s5 it with the name of the project (bolded) . , until you arrive at the document text.(# D.The Guide Specifications are being reviewed and revised. Your technical comments on any guide spec would be greatly appreciated. Also, any specs that are written "from scratch" that would benefit others could be sent to either Dion Dishong or Lori Quayle, RS110.(#  s5  DRAWING DATA REQUIRED: Location and detail drawings as needed.  s4,  REVISIONS OF THIS SECTION:  r5  CSI format, editorial changes: 2/97 Metric: Technical Update: 2/97 POINT OF CONTACT: Dennis Grevel Phone: (303) 98768580*(( [XM s4 #d `7#`(#GDISCONNECT SWITCHES Project Name (ftr B)` (#T[2/97] .16441   b-SECTION 16441 6*DISCONNECT SWITCHES PART 1: GENERAL 1.1SUMMARY A.Section Includes: [Furnishing] [and] [installing] [fusible] [and] [nonfusible], [single throw] [and] [double throw], multi-pole, safety switches.(# B.Related Sections:(# ************************************************** DELETE EITHER 01009 OR 01010. EITHER SECTION 01300 OR 01410 MUST BE USED WHEN 01010 IS USED. ************************************************** Summary of Work`(#MSection 01010 Submittals`(#MSection 01300 1.2SUBMITTALS A.General: Submittals shall be according to [Section 01009 General Information and Requirements] [Section 01300 - Submittals.] [Section 01365 Certificates of Conformance.](# B.Manufacturer's Literature: Submit [ ] copies of the manufacturer's technical data for the disconnect switches to be used on this project.(# C.Shop Drawings: Submit [ ] copies of shop drawings for the disconnect switches to be used on this project. The shop drawings shall indicate dimensions and weight loadings for disconnect switch installations. Show layout, wall brackets, mountings, and supports where applicable.(# 1.3QUALITY ASSURANCE A.Labeling Requirements: Safety disconnect switches shall be Underwriters Laboratories, Inc. (UL) listed and labeled. UL listing and labeling will not be required if it can be shown that safety disconnect switches meet the requirements of another nationally recognized testing laboratory (NRTL)(#  PART 2: PRODUCTS 2.1MATERIALS A.General: Disconnect switches shall be constructed of the manufacturer's standard materials, as listed in published product information; types and sizes shall be as indicated or as required for the installation.(# B.Operating Mechanisms: Unless otherwise indicated, switch mechanism shall be nonteasible, quick-make, quick-break. Current carrying parts shall be copper and capable of carrying rated current with minimal heating.(# C.Ratings: Unless otherwise indicated, switches shall be horsepower rated, type [HD (heavy duty)] [GD (general duty)] as defined in NEMA}&0*s's' KS 1 with current and voltage ratings and number of poles as indicated on the drawings.(# D.Enclosure: Unless otherwise indicated or required by the NEC, enclosures shall be NEMA Type 1 for indoor locations and NEMA Type 3R for outdoor locations, as described in NEMA 250.(# E.Neutral and Grounding Terminals: Enclosure shall be equipped with a neutral terminal insulated from the enclosure and a grounding terminal with metal-to-metal contact with the enclosure.(# F.Operating Handle: Enclosure shall be permanently marked so that the handle position indicates whether the switch mechanism is "On" or "Off" and the handle shall be padlockable in the "Off" position.(# G.Enclosure Door: Shall be equipped with hinges and spring latch. Door shall be interlocked with switch mechanism to prevent casual opening when the switch is "On". Interlock shall include a concealed defeat mechanism.(# H.Fuseholders: Unless otherwise indicated, fuseholders shall be reinforced, positive pressure type, designed to reject fuses which are not according to Section 16412 - Fuses.(# I.Double Throw Switches Rated Over 200 Amps: Shall have quick break operating mechanism but may have a slow-make mechanism.(#  PART 3: EXECUTION 3.1INSTALLATION A.General: Install disconnect switches as indicated, complying with the manufacturer's written instructions, applicable requirements of codes and standards, and according to recognized industry practices.(# B.Mounting Height: Unless otherwise indicated, install switches so that the top of the enclosure is 60 inches above the floor.(# C.Terminal Connections: Torque conductor terminal connections according to standard industry practice.(# D.Fuses: In fuseholders, install fuses of the type required in Section 16412 - Fuses and with current rating indicated on the drawings. When current ratings are not indicated, select fuses with current ratings according to the NEC.(# E.Nameplates: Install a nameplate according to Section 16075 - Electrical Identification, on each safety switch whose load is not readily traceable to the switch. On double throw switches install nameplates identifying power sources and loads.(#  0*s's'Ԍ-PART 4: MEASUREMENT AND PAYMENT ***************************************************** WHEN A "LUMP SUM" CONTRACT IS USED, DELETE THE TITLE PART 4: MEASUREMENT AND PAYMENT, AND BOTH ARTICLES FROM THIS SECTION. MEASUREMENT AND PAYMENT WILL BE ADDRESSED IN PART 4 OF SECTION 01010 SUMMARY OF WORK. ***************************************************** 4.1METHOD OF MEASUREMENT A.Units: The work described in this section will not be measured for payment.(# - 4.2BASIS OF PAYMENT A.Payment: No direct payment for the work described under this section will be made. Consideration for this item shall be included in the bid price for other items of the Contract.(# 0,END OF SECTION