WPC  2QB$R ZCourierw RomanCourierCourier BoldCourier Italic@`7@HP LaserJet 4HPLAS4.PRS 4dp@sQ\#n@wA6AX`AT`T`TA``66`6````AI6````T\&\hA2hXAAA2AAAAAAAA`6TTTTT}TwTwTwTwTA6A6A6A6``````````T`^```k`TTTTTTTywTwTwTwT````````A6A6A6A6kI`w6wMw6wAw6`q````AAAkIkIkIkIwQw6w6```````wTwTwT`w6`AkIw6``y``2``@#@WddddddddddddddddddddddddddddddddddddddddNEssEX`AT`````6=`:=`:AATT`BBs``uEssErkkAT`:"`soh`kss`|dBoldHPLAS4.PRS 4?f\  P6G;\#n?P2r$  X` hp x (#%'0*,.8135@8:, P age,  s5  F ooter, B , E dit. Delete the "Project Name (ftr B)" text and replace  s5K it with the name of the project (bolded) . , until you arrive at the document text.(# D.The Guide Specifications are being reviewed and revised. Your technical comments on any guide spec would be greatly appreciated.(#  s56  DRAWING DATA REQUIRED: Provide 1/4 inch scale room elevations showing extent of compartments. Provide a 1/4 inch scale floor plan of the restroom indicating by dimension the location and size of all compartments.  s4  REVISIONS OF THIS SECTION:  r5z  CSI format, editorial changes: 5/97 Metric: Technical Update: 5/97 POINT OF CONTACT: Frank Ciesel Phone: (303) 9876854o0*(( XM s4 #d `7#`(#?PLASTIC TOILET COMPARTMENTS Project Name (ftr B)` (#T[5/97] .10170   b-SECTION 10170 &PLASTIC TOILET COMPARTMENTS PART 1: GENERAL 1.1SUMMARY(# A.Section Includes: Providing and installing toilet enclosures, room entrance screens, and urinal screens.(# B.Related Sections:(# ************************************************** USE EITHER 01009 OR 01010. EITHER SECTION 01330 OR 01458 MUST BE USED WHEN 01010 IS USED. ************************************************** Structural Concrete(#`(#MSection 03310 Resilient Tile Flooring(#`(#MSection 09660 Exterior and Interior Painting(#`(#MSection 09915 Color Schedule(#`(#MSection 09999 Toilet Accessories(#`(#MSection 10810 1.2SYSTEM DESCRIPTION(# A.Toilet compartment system, including toilet enclosures, room entrance screens, and urinal screens, shall be a complete and usable system of panels, hardware, and support components. The partition system shall be provided by a single manufacturer and shall be a standard product as shown in the most recent catalog data. The partition system shall comply with FED-STD 795 and 36 CFR 1191 for areas as shown.(# 1.3SUBMITTALS(# A.General: Submittals shall be according to [Section 01009 General Information and Requirements.] [and] [Section 01330 Submittal Procedures.] [and] [Section 01331 Certificates.](# B.Manufacturer's Literature: Submit three copies of the manufacturer's descriptive data for the toilet partition system to be used on this project. Include installation and cleaning instructions.(# C.Samples: Submit samples, size 100 mm (4inch) square, of partition material in full range of manufacturer's standard colors and textures available for each type of compartment or screen indicated.(# D.Shop Drawings: Submit three copies of shop [and erection] drawings for material to be used on this project. [Drawings shall be prepared by and bear the stamp of a [registered [____________] engineer] [licensed architect.] [Shop drawings shall show layout, elevations, details of construction relative to materials, [gauges of metal,] hardware, reinforcing, fittings, mountings, and anchorings. [A bill of materials shall be furnished with the shop drawings.] Drawings shall be [same] [larger] scale as the full size Contract Drawings.(# 1.4QUALITY ASSURANCE(# ***************************************************** DELETE PHRASES BELOW THAT ARE NOT APPLICABLE. ***************************************************** A.Failure Criteria: Not limited to the following:(#}&0*s's'Ԍ1.` ` Malfunction, loosening, or breakage of any hardware.(#` 2.` ` Partition coming loose from wall.(#` 3.` ` Pilaster coming loose from floor.(#` 4.` ` Door binding on pilaster.(#` 1.5DELIVERY AND STORAGE(# A.Delivery: Components shall be delivered to the jobsite in the manufacturer's original packaging with the brand, item identification, and project reference clearly marked.(# B.Storage: Components shall be stored in a dry location that is adequately ventilated and free from dust, water, or other contaminants and shall have easy access for inspection and handling.(# 1.6PROJECT CONDITIONS(# A.Existing Conditions: Verify dimensions in areas of installation by field measurements before fabrication and indicate measurements on shop drawings.(# 1.7SEQUENCING AND SCHEDULING(# A.Room Completion: Contractor shall not install partitions until rooms in which they shall be installed have received all finishes specified and the plumbing fixtures are in place, tested and approved.(#  1.8WARRANTY(# A.Provisions: Manufacturer's standard performance and materials guarantees or warranties that extend beyond a 1 year period shall be provided.(# PART 2: PRODUCTS 2.1MATERIALS(# A.Solid Plastic, High Density Polyethylene (HDPE), 25 mm (1 inch) thick. Face shall be one seamless piece. Shall have homogenous color throughout. Edges shall be free of milling marks. Provide standard panels, doors, screens, and stiles fabricated for compartment system. Provide units with cutouts and drilled holes to receive compartmentmounted hardware, accessories, and grab bars, as indicated.(# 1.` ` Provide internal reinforcement in units for compartmentmounted hardware, accessories, and grab bars, as indicated.(#` 2.` ` Doors: Unless otherwise indicated, furnish 24 inch wide inswing doors for ordinary toilet compartments, and minimum 32 inch wide clear opening outswing doors for compartments that meet requirements of the Americans with Disabilities Act (ADA).(#` B.Panels: Height shall be [55] [58] inches.(# 1.` ` Mounting: [Continuous wall brackets] [Three aluminum stirrup brackets.](#` 2.` ` Color and Pattern: Shall be chosen by the Contracting Officer, unless otherwise indicated.(#` C.Doors: Height shall be [55] [ ] inches.(# 1.` ` Mounting: [Two] [Three] [hidden] [stirrup wrap around] hinges. (#` D.Stiles: Height shall be [82] [ ] inches.(#}&0*s's'Ԍ1.` ` Wall Mounting: [Continuous] [Three 11/2 inch aluminum stirrup] wall brackets. (#` 2.` ` Floor Mounting: Stiles attach to the floor in a [plastic] [stainless steel] [aluminum] stile shoe. Include one each level adjusting bolt on the bottom.(#` 3.` ` Overhead Bracing: Aluminum headrail.(#` 2.2HARDWARE(# A.Requirements: Furnish hardware to comply with ANSI A 117.1 and Title III of the Americans with Disabilities Act, unless otherwise indicated.(# B.Mounting Brackets: Three heavy duty anodized extruded aluminum 6063T5 alloy.(# Mounting: Tamperresistant stainless steel bolts for panels, tamperresistant stainless steel screws and plastic anchors for wall mounting. (# C.Continuous Wall Mounting: Full length [54] inch heavy duty anodized extruded aluminum 6063T5 alloy. [Wall brackets shall be predrilled every [10] inches.](# D.Hidden Hinges: Integral hinge is factory fabricated into the door and has no exposed parts. Hinges are integrated into the door and stile as a 1/2inch diameter gravity acting cam unit with 3/16 inch stainless steel center pin at bottom and 1/2 inch nylon rod at top.(# E.Wrap Around Hinges: Heavy duty extruded satin anodized Type [6463T3] [6063T3] wrap around aluminum hinges with gravity acting cams. Cam shall be constructed from 3/4 inch stainless steel pin. Height shall be Hinges shall be reinforced with steel supports, and be fully adjustable for door positioning. All hardware shall be mounted with theft resistant bolts.] (# 1.` ` For door widths 26 inches or less, provide two hinges, for door widths more than 26 inches, provide three hinges.(#` F.Latch and Keeper: [Heavy duty extruded satin anodize Type [6463T5] [6063T3] aluminum] slide latch and keeper with emergency release.(# Mounting: Use stainless steel, tamperresistant through bolts.(# G.Coat Hook: [Heavy duty cast satin anodized aluminum] [Chrome plated brass] [Type 304 cast stainless steel with number 4 finish] metal hook with door bumper.(# H.Door Pull: [Heavy duty cast satin anodized aluminum.] [Chrome plated brass.] [Type 304 cast stainless steel with number 4 finish.](# I.Floor Mounts: (# 1.` ` Pilaster Shoe: Shoe shall be theft-proof and held in place with concealed clips without exposed screws. Stainless steel surfaces shall have a No. 4 finish. Aluminum may be etched, polished or anodized as standard with manufacturer. [Shall be 20 gage ASTM A 167, Type 304 stainless steel, not less than 3 inches high, number 4 satin brushed finish.](#` J.Overhead Mounts: Continuous extruded aluminum, antigrip profile, with satin anodized finish.(# K.Caps: Same as Pilaster Shoes.(#}&0*s's'Ԍ l.Accessories: See Section 10810 Toilet Accessories.(# PART 3: EXECUTION 3.1PREPARATION(# A.Surface Preparation: Contractor shall accurately locate positions of wall bolts and floor studs required and drill holes neatly with as little disfiguration of adjacent material as possible.(# B.Condition: Area must be clean and dry prior to installation.(# 3.2ERECTION/INSTALLATION(# A.General: Assemble and install according to manufacturer's written instructions. Install compartment units rigid, straight, plumb, and level. Provide clearance of not more than 1/2 inch between stiles and panels, and not more than 1 inch between panels and walls.(# B.Partition Erection: Partitions shall be installed straight and plumb with all horizontal lines level and rigidly anchored to the supporting construction. Drilling and cutting for installation of anchors shall be at locations that will be concealed in the finished work. Secure partitions to walls with not less than two stirrups located near top and bottom. Each stirrup shall be through bolted with one-way sex bolts to partition or pilaster and bolted to wall.(# C.Doors: Doors shall have a uniform vertical edge clearance of approximately 3/16 inch and shall rest open at approximately 30 degrees when unlatched. (# D.Overhead Braced Compartments: Secure stile to floor and level, plumb, and tighten. Secure overhead brace to each stile with fasteners. Hang doors and adjust so that tops of doors are parallel with overhead brace when doors are closed.(# E.Floor Mounted Compartments: Set stile units with anchorages having not less than 2 inches penetration into structural floor, unless otherwise indicated. Level, plumb, and tighten. Hang doors and adjust so that tops of doors are level with tops of stiles when closed.(# F.Ceiling Hung Compartments: Secure stiles to supporting structure and level, plumb, and tighten. Hang doors and adjust so door bottoms are level with bottom of stiles when doors are closed.(# G.Floor and Ceiling Supported Compartments: Secure divider panels to builtin anchorage devices using concealed fasteners. Level, plumb, and tighten. Hang doors and adjust so that bottoms of doors are 12inches off the floor when doors are closed.(# 3.3ADJUSTING AND CLEANING(# A.Hardware Adjustment: Adjust and lubricate hardware for proper operation. Set hinges on inswing door to rest open approximately 30 degrees from closed position when unlatched. Set hinges on outswing doors and entrance swing doors to return to fully closed position.(# B.Clean and Protect: Clean exposed surfaces of compartments using materials and methods recommended by manufacturer, and provide}&0*s's' protection as necessary to prevent damage during remainder of construction period.(# PART 4: MEASUREMENT AND PAYMENT ***************************************************** WHEN A "LUMP SUM" CONTRACT IS USED, DELETE THE TITLE PART 4: MEASUREMENT AND PAYMENT, AND BOTH ARTICLES FROM THIS SECTION. MEASUREMENT AND PAYMENT WILL BE ADDRESSED IN PART 4 OF [SECTION 01009] [OR] [SECTION 01010]. ***************************************************** 4.1METHOD OF MEASUREMENT(# A.Units: The work described in this section will not be measured for payment.(# 4.2BASIS OF PAYMENT(# A.Payment: No direct payment for the work described under this section will be made. Contractor shall include consideration for this item in the bid price for other items of the Contract.(# 0,END OF SECTION